4 in. HD Mecanum Wheels

$58.00 – $225.00

Select option to view product code

The 4" HD Mecanum wheel comes fully assembled and ready to go and comes in three different bore sizes. A full set consists of 2 "right" wheels and 2 "left" wheels. The "right" and "left" refer t...Read More

View Full Details

Product Overview

The 4" HD Mecanum wheel comes fully assembled and ready to go and comes in three different bore sizes.

A full set consists of 2 "right" wheels and 2 "left" wheels. The "right" and "left" refer to the direction the rollers are pointing when viewing the wheel as if your about to get run over by the wheel itself. If the roller in the middle of the wheel points up and to the right, it's a "right" wheel, and up and to the left would be a "left" wheel.

The configuration of these "right" and "left" wheels is important to a mecanum drive system! Be aware that the "right" wheel should not mean that it goes on the right side of your robot. The proper configuration would be to have the wheels create an "X" pattern when viewing your robot from above and drawing lines parallel to the rollers as viewed.
This means that a "right" wheel would be the FRONT RIGHT, and the REAR LEFT position, while the "left" wheel would be in the FRONT LEFT, and REAR RIGHT, of your robot when viewed from above. All 4 wheels are required to make a Mecanum drive holonomic system to work properly.
Using these for an intake? This has been a great use of these wheels as well! The angle of these wheels help drive the object in one direction, so you can pull in the object at the same time as pushing at an angle from the intake.
This version of the wheel can handle a 200 pound load per wheel for a total 800 pound load if using as drive wheels! The interior body of this wheel is made of molded black polycarbonate, while the perimeter side plate is made of 1/8 inch thick steel, zinc plated. The perimeter plate is riveted to the interior body, and each perimeter bent tab rests on the interior body rim. This support allows for the wheel to handle more load.

Wheel Bores:

  • 1.125 in. - AKA "Bearing Bore"
    • the Original 4 in. HD Mecanum wheel
    • Use with a 1/2 in. hex hub for Heavy Duty and hex applications
  • 8mm Bore with 16mm bolt circle
    • Perfect for FTC robots
  • 1/2 Inch Hex
    • Bore molded directly into polycarbonate center body
    • While still being able to handle 200lbs of load, BE AWARE: these have a limited torque capacity. Recommended use in light duty applications (FTC robots or non-drive train FRC items such as an intake)

Roller and Axle Design:

The gray urethane rubber roller (am-3027) has a durometer rating of 80A. The roller has a Nylon core, and rides on a stationary brass tube.

Wheel Structure:

9 rubber rollers are sandwiched between 2 steel plates. The steel plates are riveted to two interior polycarbonate hubs, which form the interior of the wheel. The two interior pieces are held together by the fastening technique of the rollers being attached.

These wheels can be purchased individually as Left or Right wheels. They are sold without hubs, sprockets, or bearings.

Individual Hardware within Each Wheel:
  • 2 - HD Mecanum Plates
  • 2 - Hubs
  • 9 - Individual 4 in. Wheel Rollers
  • 9 - Brass Axle Tubes
  • 9 - M3 x 55MM SHCS
  • 9 - M3 x 0.5 in Nylock Nut
  • 18 - 0.125 in diameter Rivets


8mm Bore WheelsFor FTC Robots: If attached to a shaft or NeveRest motor, these parts are needed for each wheel. Bearing Bore Wheels
With Axle and Hub
: If driven by a shaft, these parts are needed for each wheel
  • A hub that matches the size of the drive shaft.
  • #10-24 thread-forming screws are used to fasten a hub to the wheel (we suggest 6).
  • 1/8 x 1/8 x 3/4 steel machine key (am-1043) is needed, one per wheel
With Sprocket: If driven by a sprocket, these parts are needed for each wheel
  • Flanged ball bearings (qty. 2) with 1.125 in. od: either 3/8 in. inside diameter (am-0209), or 1/2 in. i.d.
  • A sprocket (type A) with a bolt hole circle of 1.875 in. diameter mounts to the wheels' interior bolt pattern.
  • #10-24 thread-forming screws are used to fasten a hub to the wheel (we suggest 6).

1/2 inch Hex Bore
Direct Drive:
  • Simple! with a 1/2" hex shaft


  • Body Material, Inner: molded black polycarbonate
  • Body Material, Outer: 0.12 in. thick steel, zinc plated
  • Bolt Pattern: 6 holes (0.2 in. diameter) on a 1.875 in. diameter circle
  • Bore: 1.125 in, 6 mm, or 1/2 in Hex
  • Diameter: 4 in.
  • Forward / Reverse Coefficient of Friction: 0.7 (on tight pile carpet)
  • Load Capacity: 200 pounds per wheel
  • Number of Rollers: 9
  • Roller Axle: Brass Tube
  • Roller Bearing Material: Nylon spinning over brass tube
  • Roller Durometer: 80A
  • Roller Material, Inside: Nylon (white)
  • Roller Material, Outside: TPU
  • Sideways Coefficient of Friction: 0.6 (on tight pile carpet)
  • Weight: 0.9 lbs per wheel
  • Width Across Middle: 2.18 in.


Returns are accepted within 30 days of purchase.
View our return policy here.


6 reviews

  1. star star star star star 5 out of 5 stars


    These wheel are very nice, but way to expensive. Gobuilda wheels are just as good and at half the price.

    FR from Helena

    Verified Purchaser

  2. star star star star star 5 out of 5 stars

    Mecanum Wheels

    Fast delivery, received with good condition.

    YP from Singapore

    Verified Purchaser

  3. star star star star star 5 out of 5 stars

    Gravel Truck to Ferrari

    My students BEGGED me to buy these to replace the significantly cheaper VEX mecanum wheels. They theorized the new wheels would help with control and strafing. I had my doubts, but ordered anyways. I was VERY WRONG. These wheels transformed our FTC bot, the control is so much better and strafes perfectly. It took our bot from a gravel truck to a Ferrari!!

    AP from AVON

    Verified Purchaser

  4. star star star star star 5 out of 5 stars

    Don't forget to purchase all the hardware

    Wheels look great. They are well made and look pretty sturdy and smooth rolling. They do not come with any hardware. So if you do not have the right hubs or screws, you will not be able to use them I don't know if the site had a "People who order this, also ordered this" section like amazon, but if there is not one, there should be. I might have missed it. [AndyMark Response: Suggestions for different use cases, including recommended hubs and hardware, are included in the product description above.]

    SS from SOMERSET

    Verified Purchaser

  5. star star star star star 5 out of 5 stars

    Good wheels; mounting options lack detail

    These are solid and reliable wheels. The bearing mount recommendation for 3/8" bearings makes it hard to mount efficiently for FTC. More detail would be helpful to get these on 1/4" shafting. 1.125" to 0.25 bearings don't seem to be available. We made inserts and also tried a series of bearings. Other mounting options result in very wide assembly, which takes up valuable space for smaller FTC robots. Would love to see a good reference guide for the various mounting options to make these accessible to newer teams. Note from AM 11-20-19: There are three versions of these wheels, a bearing bore, a 1/2" hex bore, and an 8mm bore. The 8mm bore version is intended to be used with a nub and can be used with a 6mm (1/4") shaft.

    RY from WOODBINE

    Verified Purchaser

  6. star star star star star 5 out of 5 stars


    Perfect product, and even better support! Thank you !


    Verified Purchaser

Top of Page