Home > Gearboxes >

Banebots P60 4:1 Gearbox w/ Motor Block & Mounting Kit (am-2875)

 
Price: $46.50

Stock Status: In Stock
Qty:

  
Info Downloads More
 
Product Overview:
This gearbox is a third generation design. Don't let the small size fool you. There is a lot packed into a small package.

It is a planetary gearbox design that has been tested in the FIRST Robotics Competition for years. These are easily configurable while being small in size and low weight. Components are CNC machined for tight tolerances, using cold rolled steel gears and hardened 4140 steel carrier plates.

A standard hybrid 550/775 motor block comes with this gearbox as well as a RS-550/RS-775 mounting kits and bushings.

Specifications:
  • Gearbox Reduction: 4:1
  • Maximum torque recommendation: 35 ft-lb
  • Overall Length: 1.5 in
  • Width (square): 1.5 in
  • Output Shaft size: 0.5 in
  • Weight: 0.41 lbs
  • Mounting Holes: #10/32 thread
  • Gear Material: Steel
  • Lubrication: required when assembled

Maximum torque recommendation
We recommend maximum torque not exceed 35 ft-lb for all P60 Series Gearboxes. It is possible to mount motors that will exceed this in higher gear reductions. Higher reduction gearboxes should be utilized primarily for speed reduction. Designs utilizing a P60 gearbox / motor combination that will exceed 35 ft-lb should include a method of limiting torque to prevent damage to the gearbox.

SOME ASSEMBLY REQUIRED
Gearbox will be delivered assembled and tested; however, it will need to be disassembled to grease and mount the motor prior to use. No special tools are required, typically only a screw driver and allen wrench. A small arbor press or bench vise is useful for pushing the pinion onto the motor shaft. The gearbox MUST BE GREASED prior to use, grease IS NOT INCLUDED and must be purchased separately. We recommend our Red Tacky Grease.

MOTOR
This gearbox will mount one RS-500, RS-775 (am-2161) or similar motor. MOTOR NOT INCLUDED - Motor must be purchased separately.

MOUNTING HARDWARE INCLUDED
Gearbox includes one mounting kit. Mounting kit contains everything required to mount 1 motor including pinion, screws, and lock washers to attach the motor to the gearbox.

IMPORTANT NOTE
Mounting a large load to the end of an unsupported shaft may damage the gearmotor. The shafts on these motors are supported by two ball bearings making them fairly rugged; however, we do not recommend them to be used with large overhung loads. We recommend using a design that supports the end of the shaft. If it is not possible to support the end of the shaft, we recommend mounting the load as close to the face of the gearmotor as possible and cutting the shaft to length.

Average Customer Review: 1.5 of 5 Total Reviews: 2 Write your own review!

  0 of 0 people found the following review helpful:
 
Banebots gearbox February 2, 2017
Reviewer: James V Carr from Edison, NJ United States  
Not thrilled with product.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Banebots gear box October 31, 2016
Reviewer: bt from pottstown, PA United States  
Ordered 8 of these one box died pretty quickly, only ran it for a few minutes,  the seem good but at this point am questioning the durability.

(AndyMark response:  We will be contacting you directly in order to replace the faulty unit.)

Was this review helpful to you?


Browse products in the same categories:

Gearboxes
Gearboxes > Single Speed Gearboxes
Gearboxes > BaneBots
BaneBots
Gearboxes > Planetary Gearboxes & Stages
Browse ALL Products